b'PUSH-TO-CONNECT D.O.T. AIR BRAKE FITTINGS(FOR D.O.T. AIR BRAKE TUBE 1485)D.O.T. RECOGNIZED FOR ALL AIR BRAKE APPLICATIONS EXCEPT THOSE FOR USE BETWEEN FRAME AND AXLE OR BETWEEN TOWED AND TOWING VEHICLES.Tee TeeEnds Tube Ends Tube Tube Insertand Male Pipe Center MaleCenter Tube Pipe SwivelPART No. TubePC1400-4 1/4 PART No. Tube Pipe PART No. Tube Pipe PC1400-6 3/8PC1471-4A 1/4 1/8 PC1472SW-4A 1/41/8 PC1400-8 1/2 PC1471-4B 1/4 1/4 PC1472SW-4B 1/41/4PC1471-6B 3/8 1/4 PC1472SW-6B 3/81/4PC1471-6C 3/8 3/8 PC1472SW-6C 3/83/8 IMPERIAL TUBEPC1471-8C 1/2 3/8 PC1472SW-8B 1/21/4PC1472SW-8C 1/23/8 TO METRIC THREADTee PC1472SW-8D 1/21/2Ends Tube Connectorand Tee Tube toMale Pipe Swivel Ends Tube Metric ThreadCenter Tube CenterPART No. Tube Pipe Female Pipe PART No. Tube Size Thread SizePC1471SW-4A 1/41/8 PCDOT68MM-4-10 1/4 M10 X 1.0PC1471SW-4B 1/41/4 PCDOT68MM-4-12 1/4 M12 X 1.5 S G N I T T I FPC1471SW-6B 3/81/4 PART No. Tube Pipe PCDOT68MM-4-16 1/4 M16 X 1.5PC1471SW-6C 3/83/8 PC1478-4A 1/41/8 PCDOT68MM-6-12 3/8 M12 X 1.5PC1471SW-8C 1/23/8 PC1478-4B 1/41/4PC1471SW-8D 1/21/ PC1478-6B 3/81/490 ElbowTee Tube toEnds Tube Tee Metric ThreadCenter Male Pipe Ends TubeCenter Female PART No. Tube PipePC1472-4A 1/41/8 Pipe Swivel PART No. Tube Size Thread SizePC1472-4B 1/41/4 PCDOT69SWMM-4-12 1/4 M12 X 1.5PC1472-6A 3/81/8 PCDOT69SWMM-4-22 1/4 M22 X 1.5PC1472-6B 3/81/4 PCDOT69SWMM-6-16 3/8 M16 X 1.5PC1472-6C 3/83/8 PART No. Tube Pipe PCDOT69SWMM-8-22 1/2 M22 X 1.5PC1472-8B 1/21/4 PC1478SW-4A 1/41/8 PCDOT69SWMM-10-22 5/8 M22 X 1.5PC1472-8C 1/23/8 PC1478SW-6B 3/81/4 PCDOT69SWMM-12-22 3/4 M22 X 1.5BRASS PUSH-TO-CONNECT FITTINGS ASSEMBLY INSTRUCTIONSTemperature Range-40C to 107C (-40F to 225F)PUSH-TO-CONNECT FITTINGS FEATURE A LABOR SAVING TO CONNECT TUBE: FULL FLOW DESIGNTO DISCONNECT TUBE:Cut tube as squarely as possible. Insert tube endTHAT REQUIRES NOWith thumb and forefinger, hold down the top of into fitting, slide the I.D. of the tube over the tubeTOOLS. the insert against the fitting body and then, with support until friction is felt as tube slides past thethe other hand, pull out the tube. No tools are O-ring. Using a slight twisting motion while insert- needed.ing the tube is often helpful. After this initial friction is felt, continue to push in the tube until it bottoms firmly against the internal tube support.75'